logo
جزئیات اخبار
خونه / اخبار /

اخبار شرکت در مورد Stop Valves in a Home: Where They Go and What Each One Serves

Stop Valves in a Home: Where They Go and What Each One Serves

2026-11-17

Count the branches, not the rooms. A stop valve belongs on every supply branch a person might need to isolate without draining the house, and the count is what falls out when you walk the plan fixture by fixture and give each branch its own shutoff. Whoever quotes a total for the whole house is quoting a habit, not a rule: the same plan can be plumbed to two different totals.

One stop per branch, plus a main

Start at the meter. One valve there isolates the whole supply. Some jurisdictions also require a second valve downstream of the meter so the house can be worked on while the meter is serviced, and where that is not required, fitting one is still cheap insurance.

From there the count is mechanical. A basin takes two, hot and cold. A WC takes one. A kitchen sink takes two, plus a small stop on the dishwasher tee when the dishwasher is fed from the hot side under the sink. A washing machine takes one dual outlet body. A water heater takes one on the cold inlet. Each outdoor tap takes one inside the wall. An ice maker takes one behind the fridge.

Run that against any plan and the total is decided by the number of branches, not the number of bathrooms. If your scheme comes out far below the fixture count, some branch is leaning on the main alone, and every small repair turns into a whole house shutdown.

Renovations move the layout more than new build. Turning a bath into a shower usually keeps the branch count and drops two fixture stops. Adding an extra bathroom in a loft adds a cluster of stops, and the ones that get drawn last are usually the ones nobody can reach afterwards.

Fixture by fixture, where the stop actually sits

Branch Valve usually fitted Position that works
WC Single angle stop Beside the inlet, handle clear of the pan
Basin Two angle stops Against the cabinet back, above the trap arm
Kitchen sink Two angle stops One each side, clear of the disposal
Washing machine Dual outlet stop Inside the recessed box, outlets facing out
Water heater Full port ball valve Cold inlet, visible from the service area
Outdoor tap Stop or drain cock Inside the wall, upstream of the frost line
Fridge ice maker Small tee with stop Reachable, not behind fixed cabinetry

Most call backs on stops are placement faults, not valve faults. A stop that sits too deep behind the trap arm cannot be turned by a hand that also has to hold a torch, and the fitter ends up cutting the pipe.

Why the angle pattern wins under a basin

The supply stub leaves the wall horizontally. The fixture connector runs upward. An angle body turns that corner inside itself, so one fitting does the work of a valve and an elbow. A straight stop needs a separate elbow, and the pair eats depth in a space already crowded by the trap, the disposal and the cabinet back.

The angle body also puts the handle on the same face as the escutcheon, which means the person servicing the basin sees it first. On a deep vanity that matters more than the price difference between the two patterns.

The stops that get left out of the drawing

Four positions are routinely missed on residential plans. The first is the water heater cold inlet, the one stop that saves a whole house drain when the tank fails. The second is the outdoor tap, where the stop belongs inside the warm envelope rather than at the wall face.

The third is the ice maker. Piercing saddle valves are sold as a shortcut and they are not a service valve: once the needle has pierced the tube there is nothing to reseat, and the joint cannot be isolated for a repair without cutting it out. A tee with a proper stop costs more and ends the problem.

The fourth is the dishwasher, and any second appliance fed from the same cabinet, such as a filter tap or a boiling water unit. Both need their own isolation.

Placement rules that decide whether a stop is usable

Access comes first. A stop behind a tiled wall without an access panel is decoration. Either fit the panel or move the valve.

Give the handle room to swing. A quarter turn lever needs a clear arc roughly as long as the lever itself, so check it against the cabinet side, the pipe behind it and whatever the installer put next to it.

Keep the outlet pointing at the fixture. A stop rotated to clear a pipe often ends up aimed at the cabinet back, and the hose then makes a hard bend that loads the nut.

Orientation follows the pipe, not the room. Where the branch drops down through the floor, the stop stands on a vertical pipe and the handle sits on top, which is easy to reach but collects dust and drips. Where the branch comes out of the wall, the handle sits to one side and stays cleaner. Neither is wrong, but do not mix both within one cabinet if you want the service to go quickly.

Group the isolation where it helps. A single valve on a bathroom group lets one bathroom be drained without touching the rest of the house, and it costs almost nothing at rough in.

Record where they all are. A card inside the meter box listing the main, the heater and the group valves is the difference between a two minute job and a flooded floor.

What the body has to do

On the main, use a full port ball valve. A reduced port valve throttles the entire house and turns a marginal pressure problem into a visible one on the top floor.

On fixtures, the choice is between a quarter turn ball style and a multi turn compression style. Quarter turn closes in 90 degrees of handle travel, which is what an occupant needs in an emergency. Multi turn gives finer control and can be left part open, at the cost of a packing gland that wears and a stem that may seize if it is never moved.

Material is the other separator. Brass and brass finished zinc alloy are sold in identical shapes. A magnet settles it, and so does a light file on a hidden face.

Exercise the fixture stops once a year while the water is off for something else. A stop that has not been turned in five years is a coin toss when a fitter needs it at midnight.

Specifying a run of stops

The JF-01 brass angle valve is the body we build for basin and WC branches. The JF-02 brass angle valve covers the same duty where a project wants a different pattern on the same branch. Both are brass, both take the compression outlet the market buys against, and both come off our own tooling.

Finish options are quoted from the colour card for the model you order. Across the range the card runs to chrome plated, nickel brushed, antique brass, gold, rose gold, black, gun ash and titanium, and the JF-08 brass angle valve shows how far one family can be taken when a project needs a single finish across several rooms. Check the card against the specific model page before a finish schedule is written, because it is set per model, not per family.

Samples can travel before a stocking decision. Pull one, check the thread against the pipe you actually buy, feel the handle at the end of travel, and look at the plating under a bright light.

Next step

Send the fixture schedule from your plan, or a photograph of each stub out with a rule against it, and we will mark up where each stop belongs and which body suits that position. For a project, add the finish and the outlet size you buy against, and we will build the sample set for the rooms you are doing first.